Inspire 3 / Ronin 4D Fixed bug of R/S not working on CANBUSTER when in FIZ Control - Off Ensure you select these settings on the DJI High-Bright Remote Monitor: System Menu / General Settings / Recording Device / select TX (if no microSD is in High-Bright Monitor) or TX+SD (if a microSD is inserted into High-Bright Monitor)
Focus Range. Full / Half / Third This allows you to map the full range, the far 1/2 or far 1/3 of the lens to the full range (1-256) of the NODO knob you assign to focus. On the DJI 50mm that means from 4' - ∞. This is particularly helpful on Inspire 3 :)
Inspire 3 Only Added "Tilt to 90° Down" shortcut. "Tilt to 90° Down" functions the same as pressing "Gimbal Down" on the DJI RC Plus controller. On Inertia Wheels, a quick double press of the <Tilt> button will activate this function. A single press of that button is still "Tilt Recenter"
Ronin 2 with LiDAR Hub Unlocked the ability to adjust Focus Motor speed and invert motor direction via DJI High-Bright Monitor. System Menu / General Settings / Custom Hand Grips / Right Hand Grip
User Button Toggle between R2 User Profile 1 and 2. The button display will show the profile you will go to when you press the button. This is useful for heavy lift drone teams with landing gear on gimbal, set User Profile 1 to 2-axis and Recenter and User Profile 2 to 3-axis and Free on the Ronin 2 back screen. Also useful for on ground filming or vehicle where you want to jump between free and follow modes, in which case leave both set to 3-Axis and just change free/follow setting on profile.
RS3 Pro + RS4 Pro with LiDAR Hub Unlocked the ability to adjust Focus Motor speed and invert motor direction via DJI High-Bright Monitor. System Menu / General Settings / Custom Hand Grips / Right Hand Grip
User Button This will toggle between PTF and the 3rd position which you can set as FPV / 360° Roll / Portrait / Custom. First press of the button after powering up will be to toggle TO Position 3. User 1: PTF User 2: FPV / 360° Roll / Portrait / Custom
RS3 Pro + RS4 Pro without LiDAR Hub User Button This will toggle between PTF and the 3rd position which you can set as FPV / 360° Roll / Portrait / Custom. First press of the button after powering up will be to toggle TO Position 3. User 1: PTF User 2: FPV / 360° Roll / Portrait / Custom
To change focus motor speed and direction, use the menu on RS gimbal's OLED. Swipe Up : Dial Settings
———————————
Important Info For NODO FX to work, you will need to install Inertia Wheels firmware V2.2.2 → Update now
To set speed for each platform go: Inertia Wheels Menu / Output / CANBUSTR Settings: Rem. Spd This ensures the wheel ratios match the actual moves. 1:20 is 20 full revolutions on the wheel to be a 360° on the gimbal. Ronin 4D : 43 Inspire 3: 34 Ronin 2: 66 RS3/4 Pro: 74
New menu setting on the Inertia Wheels, Remote Speed. MENU / Output / CANBUSTR Settings / Remote Speed
Default is 34, which is the speed that means the IW ratios will match actual gimbal movement on Inspire 3. 1:1 ratio at this remote speed is very fast but you can unlock the full gimbal speed by setting this to 100.
These are the recommended remote speeds, to match wheel ratios: Inspire 3: 34 Ronin 4D: 43 Ronin 2: 66 RS3 Pro: 74
Deadband and Smoothing on R2 and RS3 Pro should be set to 0.
Any remote joystick settings on 4D or i3 menus should not affect the wheels.
CANBUSTER will remember its last setting, so no need to check it each time you power up, only when you change gimbals.
